Gilera gp800 i e 2007 service repair manual. [pdf] Gilera Gp800 I E 2007 Factory Service Repair Manual 2019-03-24

Gilera gp800 i e 2007 service repair manual Rating: 4,4/10 1191 reviews

GILERA GP 800 I.E. SERVICE STATION MANUAL Pdf Download.

gilera gp800 i e 2007 service repair manual

Engine - Lubricate the external surface of the tip with petroleum jelly grease. Stop button on front brake 54. For the front cylinder coil: - Sky Blue cable between coil and pin 10 of the control unit engine-side connector. Engine Refitting the hub bearings - Place the two shafts as shown in the figure. Maintenance The engine should be emptied by draining the oil through the drainage plug «C» placed under the engine crankcase.

Next

Gilera GP800 I.E. 2007 Workshop Service Repair Manual

gilera gp800 i e 2007 service repair manual

Right turn indicators White-Blue 3. Engine - Clean the camshaft by blowing with little com- pressed air jets, especially the retaining plate housing. Electric windshield motor cable 21. To the voltage regulator 11. Idle adjustment motor Sky Blue-Red 18.

Next

Reading : Gilera Gp800 Ie Digital Workshop Repair Manual 2007 Onwards

gilera gp800 i e 2007 service repair manual

Specific tooling 020151Y Air heater - Insert the driven pulley shaft bearing until it stops against the bottom of the seat using the specific tool. To the license plate light 2. Front Removing the front wheel - Support the scooter adequately. Resistance 120 Ohm - 2W 7. Engine - Screw the locking ring nut and tighten to the pre- scribed torque. They are placed inside the battery compartment and can be accessed by undoing the four screws «D».

Next

Gilera Gp800 Ie 2007 Factory Service Repair Manual Ebook PDF 2019 PDF Book

gilera gp800 i e 2007 service repair manual

Front wheel hub overhaul - Rimuovere da entrambi i lati lo scodellino di pro- tezione e il distanziale, colpendo con un mazzuolo in più punti. Tooling Stores code Description 001467Y001 Pliers to extract 25 mm Ø bear- ings 001467Y008 Pliers to extract 17 mm ø bear- ings 001467Y014 Pliers to extract ø 15-mm bear- ings 020357Y 32 x 35 mm adaptor 020358Y 37x40-mm adaptor 020359Y 42x47-mm adaptor. This procedure applies to the rear brake pump top- up operation;. Top-up using only the fluid specified, without exceeding the maximum level. Suspensions - Remove the hydraulic rod with the corresponding sealing gasket, the spring and the stop bushing. Specific tooling 020664Y Flywheel side crankshaft fitting tip - Tighten the seven screws «B» with the copper washers as far as they will go.

Next

GILERA GP 800 I.E. SERVICE STATION MANUAL Pdf Download.

gilera gp800 i e 2007 service repair manual

Engine - Install the coolant temperature sensor with the washer and tighten to the prescribed torque. To the right turn indicator 3. The tool will drive the fixed part seat on the crank- case and the movable part seat on the shaft, thus obtaining the correct ceramic seal preloading. Suspensions - Fit the spacer between the two ring nuts on the steering tube in the position indicated. Engine - Undo the six fixing screws and remove the cover from the opposite side.

Next

Reading : Gilera Gp800 Ie Digital Workshop Repair Manual 2007 Onwards

gilera gp800 i e 2007 service repair manual

Engine - Tighten the oil filling screw «D» to the prescribed torque. Specific tooling 020376Y Adaptor handle 020483Y 30 mm guide. Electronic ignition device Vehicle connector 67. Engine stop switch Green 28. Removing the cylinder head - The head removal operation is carried out in two separate stages, first on the rear cylinder, then on the front one. Specific tooling 020151Y Air heater - Undo the three fixing screws to replace the chain stop slider. Centre stand rear bolt nut D: Screw fixing silencer - muffler support arm E: Screw fixing catalytic converter - catalytic converter support F: Screw fixing muffler support arm - engine G: Manifold retainer clamp H:Silencer fixing screw.

Next

[pdf] Gilera Gp800 I E 2007 Factory Service Repair Manual

gilera gp800 i e 2007 service repair manual

Front right turn indicator bulb 48. Chassis - Undo the six screws fixing it to the shield back plate. Roll-over sensor: to reach it, remove the front shield. Voltage regulator: to reach it, remove the front shield. Chassis - Hold the front central cover as shown in the fig- ure. Engine - Once the scavenge oil pump fitting is finished, operate from outside the flywheel-side crankcase half.

Next

GILERA GP 800 I.E. SERVICE STATION MANUAL Pdf Download.

gilera gp800 i e 2007 service repair manual

Inspecting the cylinder head N. Maintenance - Release clip «I» and remove the filter housing cover «L». To the right control unit on the handlebar 3. To access the oil cartridge filter: - Remove mat «D». Engine - Position the belt. Engine from vehicle - Disconnect the blow-by intake pipes from the fil- ter housing.

Next