The other authorized numbers should be set by the first authorized number. I tried sending messages to tracker but it responds password wrong. I have never changed the the original password. Copy the latitude and longitude coordinates as they appear into the first half of your Geo-fence command. When its switched off or has no network service signal, it goes straight to voice mail. Wrong settings can destroy your tracker.
If your not sure on your tk102 make or model. Is there a way to put everything back to factory default or some way of setting a new password or even begin123456? Yet when I put the sim and the battery in, the now blue light flashes, but it never gets a single message or responds to the begin command. Please initialize the unit and re-set up the authorized numbers. They say it should blink every 3 seconds when searching for satellite but mine dose not blink. I want to reset the device, so that I can start from scratch, but device is not responding at all. I could not get it to communicate with my mobile phone at all. Thank you for your time.
This works on some models and clones tk102-2. Remark: This function will be out of effect after the unit moves outside the district. It seems not to drain the battery and works just fine. The manufacturer assumes no responsibility for any errors or omissions in this document. Please use the battery and charger provided by manufacturer. The 2nd unit the one that seems newer I got to respond to begin and then admin the 1st number I needed and has since not worked, the sim card is good works in both a tk 106 and cell the blue light blinks like its receiving gsm signal, but it will not respond to commands and sms, is it crap or am I missing something? As an Amazon Associate I earn from qualifying purchases.
If you buy a service or product at the external website we will earn a little commission. Olá,estou com problema no gps, ele não para de mandar mensagem acada 3 minutos, e não responde ao comando do celular,gostaria de saber como faço para começar do zero. Any suggestions how I can get the tracker to start working as it did originally? It also informs you of how much battery life is left as well as the tracker's current signal strength. Flash Magic tells us something about. S represents the set time code , 08 represents different time zone hours of tracking time, 10 represents different minutes. So ideally they should be outside in the open air. The 102 does not respond at all to a voice call.
Any change will be integrated in the latest release. Using other batteries and chargers will cause unwanted situation. Note: password must be 6 digits long. No commands work and the light flashes the same as if I had a sims card in it or out of it. I have 3 questions, 1: Can I send multiple commands in one text? Others even set them to have only broadband data. Make sure to read this manual carefully before using this product. We will get back to this error later.
Each command consists of at least 2 parameters. Battery and Charger Do charge the battery to capacity in 8 -12 hours for first use. Gelson, Have you tried dialling the tk-102 directly with your cell phone, using voice mode rather than sms commands. Your best bet would be to take the device outside, clear of any obstructions and test it once again. I cannot turn it off and on as its inside the car, i alsto tried restart123456 and begin123456 but without results. This maybe the reason the device isnt responding to your commands because your using the default password instead of the password your brother has set.
This manual shows how to operate the device smoothly and correctly. I worked a bit for a few days, then failed completely. Much more costly, but a real machine that actually works. Adelaide time zone is +9:30. It's one of the few trackers in our lineup that rely on sending text message alerts with time-stamped longitudinal coordinates.
Try to reset and to start the initialization again. My sim card if from att, i installed it , put the battery in the green light came on , then a fast blinking green light, i send some commands with no response, i drove to another area close to an att tower and i got a green blink every 3 seconds, i sent commands and it works, i went back home and the green light went back to a fast blink. Please note that specification and information are subject to changes without prior notice in this manual. The car is using by others and i need to monitor the locations. Geo-fence Geo-fence will help you to restrict the target within a certain preset area. Yes, there is no way your tracker can send you your phone coordinates.
It will alarm one time in each setting. Any change will be integrated in the latest release. To find out their location, send a text to the device and it will send you all the information you need to monitor their whereabouts in real time. Please note that specification and information are subject to changes without prior notice in this manual. The most common error message in a firmware update process is the autobaud error, and that message can nearly mean everything.