On each instrument section, attach the rack mount flange and front handles for Option 913 using the three M4x0. Back out screw 2 Figure l-6 causing the cover to unseat from the front frame. Whenever you list the serial number or refer to it in obtaining information about your instrument section, be sure to use the complete number, including the full prefix and the suffix. Calibrator Output Amplitude Accuracy Specification -10 dBm, 310. Address Switch Shown in Factory Preset Position Installation 2-23. O dB over 10 to 70 dB range Related Performance Input Attenuator Switching Uncertainty Test Test Description A signal source of known amplitude is connected to the spectrum analyzer and the analyzer is adjusted for a reference.
Voltage Selector Board and Fuse 8. In any correspondence, always provide essential information, which includes model numbers, serial numbers, or assembly part numbers. Disconnect the ac line power from the instrument sections. Familiarize yourself with each of the notes and its meaning before operating this instrument. Connect the ac line power cords. Input Attenuator Switching Uncertainty 1.
Nominal values provide useful, but nonwarranted, information about functional performance. Therefore, observe the following precautions: Information Be sure that all instruments are properly earth-grounded to prevent buildup of static charge. The major features of the include a digitally stored display, adaptive sweep, six selectable band-widths 1 Hz - 300 Hz , 30 nV sensitivity and 80 dB dynamic range. You can reset the switch to correspond to the binary equivalent of any desired decimal value indicated in Iable 2-l. Die Sammlung gibt einen kleinen Überblick, von der Vielfalt was der Hersteller über die Jahrzehnte hinweg gebaut hat. These standard features, along with optional balanced inputs and an internal rechargeable battery pack, make the ideally suited for communications, geophyical, oceanography and metrology applications. The major features of the include a digitally stored display, adaptive sweep, six selectable band-widths 1 Hz - 300 Hz , 30 nV sensitivity and 80 dB dynamic range.
These terms and conditions are subject to change at any time and without notice. Push the fuse-pull lever to the left. Note Although Figure 2-6 shows the two instrument sections connected together, they will be mounted separately in the rack. Insert the correct fuse, and push the fuse-pull lever into its normal right-hand position. These documentations are only intended for qualified technicians who are aware of the respective safety regulations. Narrowband zoom measurements are available for spans of 40 kHz or less.
If you wish to remove the information-card tray, remove the feet and tilt stands. They cause instrument damage by generating static electricity. For a detailed description and specification see the older service manuals and product catalogs, in many cases they can be downloaded from the internet or being sold as original paper version in online auctions. Manual Type Service and User Manual Pages 261 Size 41. Die Sammlung zeigt Instrumente von Hewlett Packard, im wesentlichen werden hier ältere, hauptsächlich obsolete Messgeräte vorgestellt, die in vielen Laboratorien weit verbreitet sind oder waren. When used as a network analyzer, the plots the amplitude vs. Never use styrene pellets as packaging materials.
These standard features, along with optional balanced inputs and an internal rechargeable battery pack, make the ideally suited for communications, geophyical, oceanography and metrology applications. Connect the ac line power cords. Location of Al5 Controller Assembly General Information 1-15. The tasks are grouped into six sections, The Basics will get you started. Removing the Bottom Cover 4.
The functions as a signal or as a network. Before connecting any coaxial cable to an instrument connector for the first time each day, momentarily short the center and outer conductors of the cable together. Decimal and Binary Address Codes Decimal Value S-Bit Binary Equivalen 00000 00001 00010 00011 00100 00101 00110 00111 01000 01001 01010 01011 01100 01101 01110 01111 10000 10001 10010 10011 10100 10101 10110 10111 11000 11001 11010 11011 11100 11101 11110. Pbr any assistance, contact pour nearest Hewlett-Fbckard Sales and Service Ome. When used as a signal analyzer, the provides a graphical display of the spectral components of an input signal.
They do not adequately cushion the instrument or prevent it from shifting in the carton. Remove the cover from the Al5 controller assembly. The collection shows a small overview of the variety built over decades, the were common used in many laboratories and contributed the history of electronics importantly. When used as a signal analyzer, the provides a graphical display of the spectral components of an input signal. Removing the Bottom Cover 3. Manual Type User Manual Pages 439 Size 9.
This website want to give a visual information about the older types. Be sure to install the battery with the polarity shown in Figure l-8. This lets you characterize, for example, a signal and its close-in sidebands. Für eine ausführliche technische Beschreibung sind die entsprechenden Produkt Kataloge und Geräte Manuals sehr zu empfehlen. The major features of the include a digitally stored display, adaptive sweep, six selectable band-widths 1 Hz - 300 Hz , 30 nV sensitivity and 80 dB dynamic range. When used as a network analyzer, the plots the amplitude vs.
Hewlett-Packard shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. Third Order Intermodulation Distortion Specification Intercept is greater than +5. Manual Type: Service and User Manual Pages: 261 Size: 41. The marker must be positioned at least 20 dB above the noise or the intersection of the signal with an adjacent signal, and more than four divisions up from the bottom of the display. When you turn your instrument on for the first time, you should perform the verification tests in Chapter 5. Frequency Accuracy Accuracy Marker Normal Same as center frequency accuracy + frequency span accuracy between marker and center frequency.