Vespa gts 250 workshop manual pdf. Free 2007 Vespa GTS 250 I.E Workshop Manual Download 2019-01-24

Vespa gts 250 workshop manual pdf Rating: 6,8/10 1103 reviews

VESPA GTS 250 USER MANUAL Pdf Download.

vespa gts 250 workshop manual pdf

If otherwise, adjust the right headlight with screw «A». If it varies signifi- cantly from the driving depth indicated, it means that the stud bolt has yielded. Suspensions - Remove the oil seal on the roller bearing side using a screwdriver. Characteristics This section describes the general specifications of the vehicle. Suspensions - Remove the retainer fixing the odometer cable to the mudguard indicated in the photograph - Remove the retainer fixing the brake piping to the front shock absorber upper plate - Remove the retainer fixing the brake piping to the.

Next

VESPA GTS 250 USER MANUAL Pdf Download.

vespa gts 250 workshop manual pdf

Safety rules - If work can only be done on the vehicle with the engine running, make sure that the premises are well ventilated, using special extractors if necessary;. Engine Inspecting the valve sealings - Insert the valves into the cylinder head. Headlights A Stop light B Parking light C License plate light 42. N° 2 fuse boxes in under helmet compartment 8. Also check that the tyres do not show signs of splitting at the side or irregular tread wear; if this occurs, go to an authorised workshop or at least to a workshop equipped to perform the replacement. Chassis - Remove the two turn indicators - Use a jack to lift the body so that there is enough space between the vehicle rear side and the en- gine to slide off the tank To refit, perform the steps in the reverse direction.

Next

Vespa GTS250 i.e. Factory Workshop Service repair manual

vespa gts 250 workshop manual pdf

Not only is this a complete repair manual, but it also includes all the scheduled service information, tech service bulletins, recall information. Engine Crankcase Engine half Bushing halves shaft Cat. Braking system - Check that the pistons and relevant seats exhibit no scratches. Instrument panel - Remove the rear handlebar cover;. Characteristic Axial rotor clearance Limit values admitted: 0. Rear brake calliper Removal - Remove the rear wheel. Specific tooling 020460Y Scooter diagnosis and tester Make sure that the throttle valve is supporting the stop screw.

Next

Vespa GTS250 i.e. Factory Workshop Service repair manual

vespa gts 250 workshop manual pdf

E Workshop Manual has been prepared as an introduction to the specifications, features, construction, functions, etc. Front brake stop button 22. Per i telai successivi consultare la pagina 2. Removing the driven pulley shaft bearing - Remove the clip from the inside of the cover. Suspensions - Separate the swinging arm on the engine side from the vehicle side arm.

Next

Free VESPA GTS 250 SERVICE REPAIR MANUAL PDF Download

vespa gts 250 workshop manual pdf

Removal - Remove the right and left fairings and the spoiler terminals. The immobilizer is an anti-theft system that. Tooling Stores code Description 020335Y Magnetic support for dial gauge 020357Y 32 x 35 mm adaptor 020359Y 42 x 47 mm adaptor 020360Y 52 x 55 mm adaptor 020363Y 20 mm guide 020364Y 25 mm guide. Engine Inspecting the valves - Measure the width of the sealing surface on the valve seats and on the valves. Check the depth of stud bolt driving with a gauge, as indicated in the photograph. Engine - Insert the tool in the hollows and apply the reten- tion ring - Bring in the ring's clamping screws while keeping the tool to support the pulley Specific tooling 020626Y Driving pulley lock wrench - Remove the fixing nut and the washer - Remove the stationary drive pulley half.

Next

Workshop Manuals, Service, Car Repair, Haynes Manuals Online Download

vespa gts 250 workshop manual pdf

Repair manuals provide all the information required to repair and maintain your vehicle to a high standard, whether it is changing the air filter, checking tyre pressures, to more in-depth jobs such as an engine overhaul, to changing the timing belt and head gasket. Chassis - Remove the electric connector from the saddle opening actuator - Remove the two screws shown in the photograph - Remove the clip from the transmission - Remove the actuator from the supporting bracket Rear rack. This manual contains service, repair procedures, 17. Maintenance For refitting purposes carry out the operations in the reverse order from the removal operation and respect the tightening torque of the tank cover screws. Engine Inspecting the driven sliding half-pulley - Remove the two internal grommets and the two O-rings. Right rear turn indicator 2.

Next

Vespa GTS250 i.e. Factory Workshop Service repair manual

vespa gts 250 workshop manual pdf

Engine - Fit the sprocket wheel with a new O-ring. Foldable clamps to hold the red sheathing 4. Right turn indicator lamp 20. Programmed control unit - the service key in normal condition of use : a single 0. Suspensions - Use the specific tool to fit the fifth wheel fitting on the headstock as indicated in the figure Specific tooling 001330Y Tool for fitting steering seats - Remove the steering tube - Remove the attachment bracket.

Next

VESPA GTS 250 USER MANUAL Pdf Download.

vespa gts 250 workshop manual pdf

Seat - Remove the helmet compartment - Remove the two screws shown in the photograph - Remove the saddle. Tooling Stores code Description 020481Y Control unit interface wiring 001467Y035 Bearing housing outside diame- ter 47 mm 020626Y Driving pulley lock wrench 001467Y013 Pliers to extract ø 15 mm bear- ings 020627Y Flywheel lock wrench 020467Y. Specific tooling 020376Y Adaptor handle 020456Y Ø. The immobilizer is an anti-theft system that. Foldable clamp to hold cables 3.

Next